Hello...
We have a CISCO router connected its fastethernet to a SDH and all configuration we received from the SDH owner is a "/30" network. Someone there have pointed all my networks to "xxx.yyy.zzz.30/30" and the router points it default gateway to "xxx.yyy.zzz.29/30" which is working well.
But I would like to move this router to a MT one, so I did the same. Put the IP "xxx.yyy.zzz.30/30" on a ethernet interface and have pointed the default gateway to "xxx.yyy.zzz.29/30". This just wont work! Dunno why... Am I missing some special configuration? Traffic only go out throug the default gateway, but does not return.
Didnt know what I am missing to get it working. Pls, help.
-
-
andrewluck
Forum Veteran
- Posts: 700
- Joined:
- Location: Norfolk, UK
Re: Please, need advice on SDH connection to a MT
How is that supposed to work? SDH and ethernet are different interface types, you should not plug one into the other...We have a CISCO router connected its fastethernet to a SDH
Or maybe you did not give us the whole picture and there is "something" between the Cisco's fastethernet port and your SDH line that you did not mention.
--Tom
No need to setup NAT on the router. I will post my CISCO config here soon as possible, cuz I need to grab it via console. Theres no telnet running.Do you need to setup NAT on the router?
Post the Cisco configuration here.
How is that supposed to work? SDH and ethernet are different interface types, you should not plug one into the other...
Or maybe you did not give us the whole picture and there is "something" between the Cisco's fastethernet port and your SDH line that you did not mention.
The huawey optical modem have a dual FE module which is connected to a CISCO FE. This is what we have today and we would like to remove the CISCO Router:
Optic Fiber ------- Huawey ------ CISCO FE0/0][FE0/1----- MT Router
PS: We only have that CISCO there cuz we didnt got MT working directly to the Huawey FE module, but only CISCO works so far.
Here is my CISCO configuration:
We want MT working. What else information you guys would like to know?
What could have my CISCO that MT wont do the job? I didnt figured yet why...Router#show running-config
Building configuration...
Current configuration : 1450 bytes
!
version 12.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$dwse$gJErVAyGsldPT/GsZbd7rMXF36/
!
username xxxxxx password 0 yyyyyyyyyyyyyyyyyyy
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address AAA.BBB.CCC.177 255.255.255.248
load-interval 30
duplex auto
speed auto
!
interface FastEthernet0/1
ip address XXX.YYY.ZZZ.30 255.255.255.252
speed 100
full-duplex
!
no ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 XXX.YYY.ZZZ.29
ip route wr1.eee.rrr.0 255.255.255.192 AAA.BBB.CCC.178
ip route wr2.eee.rrr.168 255.255.255.248 AAA.BBB.CCC.178
ip route wr3.eee.rrr.192 255.255.255.192 AAA.BBB.CCC.178
ip route wr4.eee.rrr.128 255.255.255.192 AAA.BBB.CCC.178
ip route wr5.eee.rrr.0 255.255.255.128 AAA.BBB.CCC.178
ip route wr6.eee.rrr.112 255.255.255.248 AAA.BBB.CCC.178
ip route wr7.eee.rrr.128 255.255.255.128 AAA.BBB.CCC.178
ip route wr8.eee.rrr.144 255.255.255.248 AAA.BBB.CCC.178
ip route wr9.eee.rrr.0 255.255.255.0 AAA.BBB.CCC.178
ip route wra.eee.rrr.0 255.255.255.0 AAA.BBB.CCC.178
ip route wrb.eee.rrr.0 255.255.255.0 AAA.BBB.CCC.178
ip route wrc.eee.rrr.0 255.255.255.0 AAA.BBB.CCC.178
ip route wrd.eee.rrr.0 255.255.255.0 AAA.BBB.CCC.178
!
!
!
!
snmp-server community LO OK
!
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end
Router#
We want MT working. What else information you guys would like to know?The only noteworthy thing I can see in that configuration is the fixed speed- and duplex setting of on of the ethernet interfaces, where auto-negotiation is turned off and it is nailed to 100-fdx. Maybe the Huawei modem also has auto-negotiation disabled with a fixed setting off 100-fdx. In that case, if the ethernet port of your MikroTik router would still be set to auto-negotiation (as it normally is if you did not change it), then it will probably not work, because finding that it can not auto-neg with the Huwei modem the standard says to fallback to 10-hdx, and that will not work when the other device is 100-fdx.
So check the setting of your MT's ethernet port.
--Tom
So check the setting of your MT's ethernet port.
--Tom
-
-
andrewluck
Forum Veteran
- Posts: 700
- Joined:
- Location: Norfolk, UK