Hello
I bought an CRS109-8G-1S-2HnD-IN. Then I started to play around. A bit Wifi, a bit Routing. It seems to work but it was slow.
So I simplified my setup. Now it works as a pure switch. Everything what isn't needed is disabled. Two ports are used. One for a client and one wire to my previous router.
But it is still slow. A speedtest show me that I got ~ 0.25mbit through the switch.
If I put my client directly behind the router I got ~ 12mbit. Thats what I get over my ADSL2 connection. This value is good.
Is there maybe a bad configuration in my switch or are there any other ideas what could be wrong?
The cpu is at 2%. There is no problem.
Cheers
Re: A slow CRS109
Hi,
Have you checked speed/ duplex on interfaces? Do you have any firewall rules? Are you using bridges? Do the 2 ports belong to the same master port?
Have you checked speed/ duplex on interfaces? Do you have any firewall rules? Are you using bridges? Do the 2 ports belong to the same master port?
Re: A slow CRS109
To be sure that you really set it up as a switch, please post your config
Re: A slow CRS109
My link status is 1G. Looks ok.
Thats my config:
Thats my config:
Code: Select all
[admin@ap] > /export
# dec/01/2016 11:47:06 by RouterOS 6.37.3
# software id = IL2B-MHDQ
#
/interface ethernet
set [ find default-name=ether2 ] master-port=ether1
set [ find default-name=ether3 ] disabled=yes
set [ find default-name=ether4 ] disabled=yes
set [ find default-name=ether5 ] disabled=yes
set [ find default-name=ether6 ] disabled=yes
set [ find default-name=ether7 ] disabled=yes
set [ find default-name=ether8 ] disabled=yes
set [ find default-name=sfp1 ] disabled=yes
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-b/g/n channel-width=20/40mhz-Ce distance=indoors frequency=auto mode=ap-bridge ssid=MikroTik-A7F116 wireless-protocol=802.11
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip dhcp-client
add dhcp-options=hostname,clientid disabled=no interface=ether1
/ip dns
set cache-max-ttl=1d1s
/ip service
set telnet disabled=yes
set ftp disabled=yes
set api disabled=yes
set winbox disabled=yes
set api-ssl disabled=yes
/lcd
set enabled=no
/lcd interface pages
set 0 interfaces=wlan1
/system clock
set time-zone-name=Europe/Berlin
/system identity
set name=ap
/system ntp client
set enabled=yes server-dns-names=0.de.pool.ntp.org,1.de.pool.ntp.org,2.de.pool.ntp.org,3.de.pool.ntp.org
/system routerboard settings
set protected-routerboot=disabled silent-boot=yes
/system watchdog
set watchdog-timer=no
/tool mac-server
set [ find default=yes ] disabled=yes
add
/tool mac-server mac-winbox
set [ find default=yes ] disabled=yes
add
Re: A slow CRS109
Which ports are you plugged into now?
Re: A slow CRS109
The ports ether1 and ether2. The other ports are disabled.
Re: A slow CRS109
What does "interface ethernet monitor ether1,ether2" command show?
Re: A slow CRS109
This output:What does "interface ethernet monitor ether1,ether2" command show?
Code: Select all
[admin@ap] > /interface ethernet monitor ether1,ether2
name: ether1 ether2
status: link-ok link-ok
auto-negotiation: done done
rate: 1Gbps 1Gbps
full-duplex: yes yes
tx-flow-control: no no
rx-flow-control: no no
advertising: 10M-half 10M-half
10M-full 10M-full
100M-half 100M-half
100M-full 100M-full
1000M-half 1000M-half
1000M-full 1000M-full
link-partner-advertising: 10M-half 10M-half
10M-full 10M-full
100M-half 100M-half
100M-full 100M-full
1000M-half 1000M-full
1000M-full
-- [Q quit|D dump|C-z pause]
Re: A slow CRS109
So there is obviously no config problem?
Maybe my hardware is broken and I should try a new device?
0.25mbit is very slow. Every porn stream would lag. Thats a mess (:
Maybe my hardware is broken and I should try a new device?
0.25mbit is very slow. Every porn stream would lag. Thats a mess (:
Re: A slow CRS109
This configuration is very simple and should not cause any performance issues.
Try to enable switching on different ports and do the same test.
Try to enable switching on different ports and do the same test.
Re: A slow CRS109
I tried the Mikrotik in an other setup. I got 100mbit routed through the box with a cpu usage between 15 and 30 percent.
That looks much better.
It seems there is an problem between my router (a Fritzbox) and the Mikrotik. I had never seen such a performance problem behind this Fritzbox. But the Mikrotik works also great.
At the moment I can't say what is realy wrong there. Maybe I need to drop my fritzbox out of the window.
But thanks for your help!
That looks much better.
It seems there is an problem between my router (a Fritzbox) and the Mikrotik. I had never seen such a performance problem behind this Fritzbox. But the Mikrotik works also great.
At the moment I can't say what is realy wrong there. Maybe I need to drop my fritzbox out of the window.
But thanks for your help!
Re: A slow CRS109
Hello x70b1,
I'm having the same issues as you describe with my fritzbox and my Mikrotik wAP ac. Did you have found an solution for this?
I'm having the same issues as you describe with my fritzbox and my Mikrotik wAP ac. Did you have found an solution for this?