Hi my name is chris,
i bought the Wireless wire kit, for connecting two building over 130meters.


Last Link Down Time Aug/24/2020 11:15:57
Last Link Up Time Aug/24/2020 11:16:05
Link Downs 346
Frequency 58320
Signal 30
MCS 1
PHY Rate 385.0 Mbps
RSSI -66 dBdB
TX Sector 27
TX Sector Info center
RX Sector 96
Distance 136.56 mm
Actual MTU 1500
Station Bridge
RouterOS v6.47.2 (stable)
Uptime 1d 03:45:33
Free Memory 206.7 MiB
Total Memory 256.0 MiB
CPU ARMv7
CPU Count 4
CPU Frequency 716 MHz
CPU Load 0 %
Free HDD Space 2340 KiB
Total HDD Size 15.3 MiB
Sector Writes Since Reboot 5 693
Total Sector Writes 7 143
Bad Blocks 0.0 %
Architecture Name arm
Board Name wAP 60G
Version 6.47.2 (stable)
Build Time Aug/13/2020 06:39:44
Factory Software 6.44.6


Master:
Frequency 58320
Signal 30
MCS 2
PHY Rate 770.0 Mbps
RSSI -68 dBdB
TX Sector 27
TX Sector Info center
RX Sector 96
Distance 136.51 mm

Uptime 1d 02:54:02
Free Memory 206.3 MiB
Total Memory 256.0 MiB
CPU ARMv7
CPU Count 4
CPU Frequency 716 MHz
CPU Load 0 %
Free HDD Space 2256 KiB
Total HDD Size 15.3 MiB
Sector Writes Since Reboot 10 141
Total Sector Writes 18 951
Bad Blocks 0.0 %
Architecture Name arm
Board Name wAP 60G
Version 6.47.2 (stable)
Build Time Aug/13/2020 06:39:44
Factory Software 6.44.6


The settings are default, my problem is, that the connection is not stable and I don't know why this happen.

Is there a option for optimization?

I heard, recommended are this shields? http://24.multimediahd.pl/en/60ghz/96-s ... s-cnc.html ? Is there other trusted shops?
Should i change something on the setup?

TX Power? If yes, which value?
Firmware? if yes, which would be the best for me, should i switch to beta? Other Recommendations?

best regards

Chris

Hello,

RSSI is too low, set tx-sector to auto and check if that improves situation.

Hi, can you explain, where i can do this?

best regards

Chris

[admin@MASTER] /interface w60g> print
Flags: X - disabled, R - running
0 name="wlan60-1" mtu=1500 l2mtu=1600 mac-address=48:8F:5A:XXX:XXarp=enabled arp-timeout=auto region=no-region-set mode=bridge ssid="MikroTik-4da723" frequency=58320 default-scan-list=58320,60480,62640,64800 password="XXXXXXXXX" tx-sector=auto put-stations-in-bridge=bridge
isolate-stations=yes

[admin@SLAVE] /interface w60g> print
Flags: X - disabled, R - running
0 R name="wlan60-1" mtu=1500 l2mtu=1600 mac-address=48:8F:5A:XXX:XX arp=enabled arp-timeout=auto mode=station-bridge ssid="MikroTik-4da723" frequency=auto default-scan-list=58320,60480,62640,64800 password="XXXXXXXX" tx-sector=auto put-stations-in-bridge=none isolate-stations=yes
[admin@WlanBridgeGui

everything seems to be in order, are devices aligned correctly? Is there anything blocking path?

hi,
there is nothing between the both devices.
Schould i set the frequency on the slave also to a static value?

Have I to adjust a setting or buy something to get a better signal?

best regards
chris

Downgrade RouterOS to 6.45.9 (long-term). We have a lot of issues with 6.47 and up on all 60GHz MikroTik devices.
Ref #1: viewtopic.php?f=7&t=133374&start=300#p812033
Ref #2: viewtopic.php?t=161887#p798971

hi,

i have done this at 11am, connection is still alive, but the signal is still below 30.


best regards

Chris

Hi,
the connection is broken 4 times, signal is still low, can I do something to improve the connection?

thanks for your help.

best regards

Chris

Hi, the connection is still not working correctly.

Last Link Down Time Aug/26/2020 09:24:49
Last Link Up Time Aug/26/2020 09:24:51
Link Downs 433
Connected
Frequency 58320
Remote MAC 48:8F:5A:4D:A7:24
Signal 40
MCS 1
PHY Rate 385.0 Mbps
RSSI -67 dB
TX Sector 27
TX Sector Info center
RX Sector 96
Distance 135.95 m

what can i do?
Attached a picture of the situation, i marked the other ap.

best regards

Chris

It is still not working.

These "Anti Noise Shield" are helping for a better connection?

Can i use on one end the MikroTik RBwAPG-60ad and on the other end the RBLHGG-60ad to get a better connection?

best regards

Chris

From picture it seems, that nearby trees may be covering line of sight during winds, please try with higher frequencies as well.