RBLHGR&R11e-LTE6 low speed

se64plus · Thu Oct 22, 2020 1:35 pm

Hello. I need help.
I have LTE base a station 500m away. My Iphone gets 30-40mbits dl rate, my Mikrotik gets 1-2 mbits. Band ID both on the Iphone and Mikrotik is 3 (1800mhz).
Is it something wrong with the device parameters? Or am I missing something?
Thank you.

Mikrotik parameters:
Current Operator UA-KYIVSTAR
LAC 52800
Current Cell ID 48798496
eNB ID 190619
Sector ID 32
PHY Cell ID 489
Access Technology Evolved 3G (LTE)
IMEI 356662100107454
IMSI 255030620482763
UICC 8938003992792562991
Primary Band B3@20Mhz earfcn: 1500 phy-cellid: 489
CA Band
Session Uptime 00:57:00
RSRP -70 dBm
RSRQ -8.5 dB
SINR 17 dB
CQI 13
Status
Last Link Down Time
Last Link Up Time Oct/22/2020 12:31:39
Link Downs 0
Registration Status registered
PIN Status ok
Functionality full

Iphone parameters:

SiB · Thu Oct 29, 2020 3:08 pm

Mikrotik parameters:
Current Cell ID 48798496
eNB ID 190619
PHY Cell ID 489
Primary Band B3@20Mhz earfcn: 1500 phy-cellid: 489

VS

Means they are differ Antennas/Towers and you not should compare them.
The same eNB / Cerrent Cell ID / earfcn&pci-cell-id give confirmation that you are connect to the same Bts/Tower/SectorAntenna - now it's not true.

You can do a Cell Monitor and even Cell Lock to detected earfcn & pci to select that who give you best speed and signal.

wichets · Thu Oct 29, 2020 3:14 pm

Hello. I need help.
I have LTE base a station 500m away. My Iphone gets 30-40mbits dl rate, my Mikrotik gets 1-2 mbits. Band ID both on the Iphone and Mikrotik is 3 (1800mhz).
Is it something wrong with the device parameters? Or am I missing something?
Thank you.

Mikrotik parameters:
Current Operator UA-KYIVSTAR
LAC 52800
Current Cell ID 48798496
eNB ID 190619
Sector ID 32
PHY Cell ID 489
Access Technology Evolved 3G (LTE)
IMEI 356662100107454
IMSI 255030620482763
UICC 8938003992792562991
Primary Band B3@20Mhz earfcn: 1500 phy-cellid: 489
CA Band
Session Uptime 00:57:00
RSRP -70 dBm
RSRQ -8.5 dB
SINR 17 dB
CQI 13
Status
Last Link Down Time
Last Link Up Time Oct/22/2020 12:31:39
Link Downs 0
Registration Status registered
PIN Status ok
Functionality full

Iphone parameters:

you can enable CA band as this model can support Carrier Aggregation (CA) this model is look like the 2XCA support
let try to enable it you can get double speed.

Rikjaard · Thu Oct 29, 2020 8:17 pm

you can enable CA band as this model can support Carrier Aggregation (CA) this model is look like the 2XCA support
let try to enable it you can get double speed.

Can you point to configuration for Carrier Aggregation CA please i would like to try it. Thank you in advance from slow learner.

I only just realised that sxt lte with two chips cant aggregate both APNs i only found example of Failover.
Anyhow i like mikrotik its make my brain work to get ineternet that everybody has parents deliver to the Lap(top) Have fun,

SiB · Thu Oct 29, 2020 10:43 pm

wichets

you can enable CA band as this model can support Carrier Aggregation (CA) this model is look like the 2XCA support
let try to enable it you can get double speed.

CA feature is ENABLED as default at R11e-LTE6.
Even if you select one BAND and then you can still connect with CA with it as INTRA. You can still do a Freq or Cell Lock who just select PrimaryBand but still CA can be connected.
CA can be connected by your TOWER eNB decision, our lte module cannot change that policy.

We not have a official way to disable CA.

RBLHGR&R11e-LTE6 low speed

RBLHGR&R11e-LTE6 low speed

Re: RBLHGR&R11e-LTE6 low speed

Re: RBLHGR&R11e-LTE6 low speed

Re: RBLHGR&R11e-LTE6 low speed

Re: RBLHGR&R11e-LTE6 low speed