I try RC3 version and after time (15min - 3 hours) my router was break down ! I can't ping it. I try it on 2 PC - whitch work ok with ver. 2.9.xx with same configuration !
I uninstalled Dude and calea package because it hang my MT pernamently !
My router hang again! It's unstable!

Plase help me.

I had the same problem recently with a critical access point, upgraded to RC4 and its been fine since. It appears to have also "fixed" those pesky "....extensive data loss" issues.


Regards

Ok. I upgrade it now to rc4 )

I update to RC4 - same problems !
My CPU was hangs up with 100% CPU load !

Try a reset-configuration.
Then re-configure your router from the ground up.

This should get you back up and running.

Uf. It's hard work, but I try it.

I update to RC4 - and ......
extensive data loss
extensive data loss again

buuuuu

Way !?!

Torin

I put new configuration - manualy (not import) - still problem with 100% CPU usage !

Please, repair this important bug!
Why mikrotik doesn't have resource monitor by packages?
I need see how many memory, cpu take some packages, for example:
CPU MEM
dude 10% 1250kb
dhcp 1% 200kb
system 25% 125kb
...

This monitoring may resolve many broblems, I think so.

What are you using as a router? PC, RB532, etc?

No I try RB133 and PC with 2GHz Celeron.
I have same problem with both platforms.

I put new configuration - manualy (not import) - still problem with 100% CPU usage !

Please, repair this important bug!
Why mikrotik doesn't have resource monitor by packages?
I need see how many memory, cpu take some packages, for example:
CPU MEM
dude 10% 1250kb
dhcp 1% 200kb
system 25% 125kb
...

This monitoring may resolve many broblems, I think so.

I think I told in one of the topics, that when you have a dude package after the reboot it loads all the snmp mibs and that could take few minutes - cpu 100% you should wait few minutes.

I wrote (top), that I don't use dude and calea package!

I disabled this packages! But this issue don't resolve my problem.

check your hardware, i am running RC4 on different hardware and have no problems with 100% CPu even on RB112

My HW is OK ) When I red this forum, many peoples has same problem. I try RC4 on:

3x PC
1x RB133

on 2.9.xx version on some HW - no problem !!!!!!!!

so, to repeat your problem all i have to do is to install rc4 on a box?

even on clean install your box stays 100% cpu? (if you can, save backup (2 copies) do system reset-configuration and see what happens

I'm seeing this problem but it only happens after I login to the router via SSH or at the console. I can quick jump into resources and it sits at 2-5% then after another command or 2, it shoots to 100% (can tell because my typing is very slow). The commands are just print or monitor commands, no config changes. I'm seeing this in RC4 aswell.

Nik

This appears to be a problem with the system formatting your proxy drive regardless whether the proxy is enabled or disabled. I let mine go for about an hour and now its fine. I had a second 20gb drive for proxy attached to the system though.

I don't use web proxy and I use Flash drive as my system and boot medium.
I return my stable 2.9.xx versions.

3.xx version is it not stable today !
I try something for resolve this problem. I didn't resolve it.

I am wait for new RC5 or 3.0 stable final version.

) I think so. It's slow, unstable !

if neither of you have submitted tickets to support with supouts then don't complain that it's not fixed in rc5. thank you.

I am also having serious issues. I'm using 3.0.rc4. I have two brand new RB532a R5 boards that are locking up after a few minutes to a few hours. They were running perfect with 2.9.46 but as soon as I loaded 3.0.rc4, they started locking up. I even did a reset-configuration to one of them, then set up a very basic configuration. It continues to lock up. It looks like I have to go back to 2.9.46 until a new version of 3.0 comes out.

I am also having serious issues. I'm using 3.0.rc4. I have two brand new RB532a R5 boards that are locking up after a few minutes to a few hours. They were running perfect with 2.9.46 but as soon as I loaded 3.0.rc4, they started locking up. I even did a reset-configuration to one of them, then set up a very basic configuration. It continues to lock up. It looks like I have to go back to 2.9.46 until a new version of 3.0 comes out.

have you contacted the support about this issue? what kind of configuration you have on this router that is crashing?

I have very simple config ! I try reset it !
I can't make RIF file because when my MT was broken, this options didn't work!