Hello everyone.
I have strange problem with router mikrotik hAP ac2, I set static ip 192.168.88.2, try to conect to router by winbox but i can't find it. I try to reset router to basic settings but i can't. Every time when i put powet cabel in to the router 2 led blinking (port 4 and power led). What can I do with this ? Please help.
Re: Mikrotik hAP ac2 blinking ports
What port of the router is your computer connected to (I'm guessing 4, but confirming)?
Re: Mikrotik hAP ac2 blinking ports
Even if i don't use any port and have only power cabel conecting with router port 4 and power led blinking. I don't see router on winbox on every port. It's start when i conect for first time, reset router and leave sesion with adres ip: 0.0.0.0.What port of the router is your computer connected to (I'm guessing 4, but confirming)?
I can't restart router with buton, and probably can't boot this router or I don't know how to do it.
Re: Mikrotik hAP ac2 blinking ports
There is a reset button near the power jack.
1 - Disconnect the power cord from the unit
2 - Hold the reset button and do not release.
3 - Plug the power cord in and wait until the ACT light starts flashing.
4 - Now release the button to clear configuration.
5 - Wait for a few minutes for the router to clear and restore the factory settings.
5 - Connect your computer to port 3 on the Mikrotik router
6 - Open your web browser and connect to http://192.168.88.1 if the router has been reset you will not be asked for a password and should be redirected to the quickset page.
Pretty much the same for all Mikrotik rotuers.
1 - Disconnect the power cord from the unit
2 - Hold the reset button and do not release.
3 - Plug the power cord in and wait until the ACT light starts flashing.
4 - Now release the button to clear configuration.
5 - Wait for a few minutes for the router to clear and restore the factory settings.
5 - Connect your computer to port 3 on the Mikrotik router
6 - Open your web browser and connect to http://192.168.88.1 if the router has been reset you will not be asked for a password and should be redirected to the quickset page.
Pretty much the same for all Mikrotik rotuers.
Re: Mikrotik hAP ac2 blinking ports
Like i said i can't do this. I have the same problem like guy on this video https://www.reddit.com/r/mikrotik/comme ... nd_port_4/There is a reset button near the power jack.
1 - Disconnect the power cord from the unit
2 - Hold the reset button and do not release.
3 - Plug the power cord in and wait until the ACT light starts flashing.
4 - Now release the button to clear configuration.
5 - Wait for a few minutes for the router to clear and restore the factory settings.
5 - Connect your computer to port 3 on the Mikrotik router
6 - Open your web browser and connect to http://192.168.88.1 if the router has been reset you will not be asked for a password and should be redirected to the quickset page.
Pretty much the same for all Mikrotik rotuers.
Re: Mikrotik hAP ac2 blinking ports
I'm not watching somebodies video - especially on Reddit.
You said you don't know how, so I told you how. What does it not do?
Next step would be a Netinstall.
You said you don't know how, so I told you how. What does it not do?
Next step would be a Netinstall.
Re: Mikrotik hAP ac2 blinking ports
AFAIK, there’s no known issue causing this. The suggestion you were provided with already is the proper troubleshooting procedure...
1. Netinstall 6.48.6 (latest long term): https://wiki.mikrotik.com/wiki/Manual:Netinstall
2. Try another power supply (any MikroTik supplier should have some in stock if you're not comfortable with the requirements)
3. Contact support.
1. Netinstall 6.48.6 (latest long term): https://wiki.mikrotik.com/wiki/Manual:Netinstall
2. Try another power supply (any MikroTik supplier should have some in stock if you're not comfortable with the requirements)
3. Contact support.
Who is online
Users browsing this forum: No registered users and 19 guests