MikroTik

Hello

I have 2 questions about the RBM33G and especially it's mPCIe/M.2 ports.
https://mikrotik.com/product/rbm33g#fnd ... ifications

1. If I understand right, there is an USB 2 bus present on port mPCIe#0 & mPCIe#1 (if jumper accordingly set of course), but is there a PCIe bus connected to both ports also???

2. The M.2 port has exclusively a PCIe bus, no USB at all, right?




Thank you

2. The M.2 port has exclusively a PCIe bus, no USB at all, right?

M.2 is only M.2 port.
.
https://i.mt.lv/cdn/rb_files/RBM33-1565865697.png

Yes I know that diagram, but it's c*** I don't trust it because:

1. It's clearly stated that M.2 slot has a PCIe bus. But the "miniPCIe slot 2" there is nothing indicating what that line to the SoC is about (we could thinks it's a PCIe also, but not sure. "miniPCIe" is a connector specification, not a bus!!!).

2. SIM slot 2 & 1 are connected to the SoC according to that diagram, which is actually totally false because it has nothing to do with the SoC, it's electrically connected directly to the corresponding mPCIe slot.



In other words, I don't trust it.

M.2 is only M.2 port.

You mean PCIe bus?

Because M.2 specifications defines PCIe bus and/or USB2/3, I2C,...

Saying M.2 is only M.2, is actually not really clear. But I assume you want to say "PCIe bus only" right?

M.2 is only M.2 port.

You mean PCIe bus?

Because M.2 specifications defines PCIe bus and/or USB2/3, I2C,...

Saying M.2 is only M.2, is actually not really clear. But I assume you want to say "PCIe bus only" right?

.
MediaTek MT7621A: https://www.mediatek.com/products/homeN ... /mt7621n-a give info:

• PCI-Express: Host(3x) but MikroTik give info about 2x
• USB: USB 3.0 (1x), USB 2.0 (1x)
• Flash: SPI, SLC NAND
• embedded 5p GbE Switch

STORAGE
viewtopic.php?f=3&t=134737&p=723757&hilit=m33g#p723757
Now you should see that it's just work for ssd drive.

Connection Diagram
In HiRes photo https://i.mt.lv/cdn/rb_images/1722_hi_res.png are 3x mPCIe like MediaTek describe.

QuickGuide > USB Jumper > I change the queue of original sentence.

Jumper ON:
When loaded, the jumper enables the USB 3.0 port.
Normally you can use the LTE modem in the J8 (lefthand side) slot, and use a 802.11 wireless card in the J10 slot. In this case, you can leave the jumper on, as most
wireless cards operate on a PCI express.

Jumper OFF:
Remove the jumper to switch the USB 2.0 lines to the J10 (central) miniPCIe slot (USB 3.0 lines remain enabled to the USB port).
This is required if you need to use two cellular modems in the device.
Removing the jumper enables the use of a secondary cellular modem in the central J10 slot, but disables the USB 2.0 functionality of the USB port, while USB 3.0 can still be used on the USB port.

Summary:

• J8 = PCIe 0 = Left = LTE normal
• J10 = PCIe 1 = Center = WiFI normal or LTE
• J400 = PCIe 2 = Right = M.2 slot
• USB: 2.0+3.0 or only 3.0

Your Diagram with some change's:

Ok thank you.

Hi, does this mean the sim card slots are not switchable with 1 LTE mini-PCIe?

andryan

Hi, does this mean the sim card slots are not switchable with 1 LTE mini-PCIe?

"switchable " SIM Slot are in SXTR/LtAP/LtAP mini . Not here .

andryan

Hi, does this mean the sim card slots are not switchable with 1 LTE mini-PCIe?

"switchable " SIM Slot are in SXTR/LtAP/LtAP mini . Not here .

Thanks for the confirmation, SiB!