I'm pretty new on the forum, networking and Mikrotik products as well.
I decided to start learning routeros from scratch but as a first thing I'd like to use a hap ac2 as main home network router. I have 1Gbps FTTH and the hap is connected to the ONT.
I set the pppoe client up on ether1, basic firewall config (the basic one from mikrotik) and the other interfaces are bridged.
Now, I just can get up to 300Mbps upload speed instead of something close to 1 Gbps. By reading the specs and speed test I assumed hap ac2 was capable to manage such 1Gbps speed with a basic firewall rules set.
Config down below.
Any suggestion or explanation on how I can't get the full speed?
Thanks
Code: Select all
# feb/26/2023 21:49:05 by RouterOS 6.49.7
# software id = 35QG-FUDM
#
# model = RBD52G-5HacD2HnD
# serial number = HCY081Y2GKN
/interface bridge
add admin-mac=18:FD:74:77:0C:48 auto-mac=no comment=defconf name=bridge
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-b/g/n channel-width=20/40mhz-XX \
disabled=no distance=indoors frequency=auto installation=indoor mode=\
ap-bridge ssid=MikroTik-770C4C wireless-protocol=802.11
set [ find default-name=wlan2 ] band=5ghz-a/n/ac channel-width=20/40/80mhz-XXXX \
disabled=no distance=indoors frequency=auto installation=indoor mode=\
ap-bridge ssid=MikroTik-770C4D wireless-protocol=802.11
/interface vlan
add interface=ether1 name=vlan_fibra vlan-id=835
/interface pppoe-client
add add-default-route=yes disabled=no interface=vlan_fibra name=pppoe-fibra \
password=*********** user=*************
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip pool
add name=default-dhcp ranges=10.10.10.10-10.10.10.100
/ip dhcp-server
add address-pool=default-dhcp disabled=no interface=bridge name=defconf
/interface bridge port
add bridge=bridge comment=defconf interface=ether2
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
add bridge=bridge comment=defconf interface=wlan1
add bridge=bridge comment=defconf interface=wlan2
/ip neighbor discovery-settings
set discover-interface-list=LAN
/interface list member
add comment=defconf interface=bridge list=LAN
add comment=defconf interface=ether1 list=WAN
/ip address
add address=10.10.10.254/24 comment=defconf interface=bridge network=10.10.10.0
/ip dhcp-server network
add address=10.10.10.0/24 comment=defconf dns-server=10.10.10.254 gateway=\
10.10.10.254
/ip dns
set allow-remote-requests=yes servers=8.8.8.8,8.8.4.4
/ip dns static
add address=10.10.10.254 comment=defconf name=router.lan
/ip firewall filter
add action=accept chain=input comment=\
"defconf: accept established,related,untracked" connection-state=\
established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=\
invalid
add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp
add action=accept chain=input comment=\
"defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" \
in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" \
ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" \
ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" \
connection-state=established,related
add action=accept chain=forward comment=\
"defconf: accept established,related, untracked" connection-state=\
established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" connection-state=\
invalid
add action=drop chain=forward comment="defconf: drop all from WAN not DSTNATed" \
connection-nat-state=!dstnat connection-state=new in-interface-list=WAN
/ip firewall nat
add action=masquerade chain=srcnat out-interface=pppoe-fibra
/system clock
set time-zone-name=Europe/Rome
/system identity
set name=RouterBolo
/tool mac-server
set allowed-interface-list=LAN
/tool mac-server mac-winbox
set allowed-interface-list=LAN
