Hello,
I have a test setup which has a signal of -54dB it runs on both sides on a intel platform P4 2.8Ghz (775 socket) and P3 1Ghz (serverworks chipset) it uses both an MT 5211 radio that runs on 2.8.24.
But my troughput is low for it must can be. On 5Ghz-turbo and 5800 it stays on 43mbit, and when i enable nstreme on de systems i had only 23 mbit of data stream trough the router. This problem i had in bridged mode en in routed mode. My CPU does not rise to the 100% but max to 60% on the P3
greets,
Johan
-
-
stephenpatrick
Forum Veteran
- Posts: 702
- Joined:
- Location: UK
- Contact:
No,
It couldn't be the problem because the nodes stays now 4 meters beyond. I would place them for a 20 KM link but i would test the troughput first.
I can garantee there is no interference.
PS. Maybe could it be that the EMF from the cpu's causes this problem?
but as it uses 2 channels could it use to 5820Mhz?
greets,
johan
It couldn't be the problem because the nodes stays now 4 meters beyond. I would place them for a 20 KM link but i would test the troughput first.
I can garantee there is no interference.
PS. Maybe could it be that the EMF from the cpu's causes this problem?
but as it uses 2 channels could it use to 5820Mhz?
greets,
johan
-
-
stephenpatrick
Forum Veteran
- Posts: 702
- Joined:
- Location: UK
- Contact:
I've tried jet a another p3 motherboard i've got a very badly result from approx. 300Kbit to max 2 Mbit.
But which chipset does works fine, is there a compatible list eith different chipsets of differt platforms.
I've got 1 new server it has a intel 915 chipset. Does someone have a config with the 915 to.
greets,
Johan
But which chipset does works fine, is there a compatible list eith different chipsets of differt platforms.
I've got 1 new server it has a intel 915 chipset. Does someone have a config with the 915 to.
greets,
Johan
-
-
denialsander
newbie
- Posts: 47
- Joined:
- Location: Norway
-
-
denialsander
newbie
- Posts: 47
- Joined:
- Location: Norway
-
-
denialsander
newbie
- Posts: 47
- Joined:
- Location: Norway
Johan (the initial poster) wrote this:I suggest you to use the latest stable release... With beta12 I got only 2 or 3 Mbps, but with 2.8.23 i've got 46 Mbps on more than 40 km.newest betas....
So I guess this doesn't apply to his problems. My best guess is still the distance between the nodes. I tried again yesterday: Bandwidth between my two 5GHz nodes fell dramatically as I moved them closer to each other (parabolic dishes).it uses both an MT 5211 radio that runs on 2.8.24.
-
-
stephenpatrick
Forum Veteran
- Posts: 702
- Joined:
- Location: UK
- Contact:
Seems like CPU problem... What procesors did you use? Nstreme is very CPU sensitive... The more, the better :)I used 2.8.10 43 Mbit and 2.8.24 without nstreme 43 mbit with nstreme 23 MbitJohan, I've had similar problems as you've had. Tested at 2M and throughput was around 45-50mbps. Similar type of setup with 2 Intel-based servers just doing a b/w test with the newest betas....
I use a 2.8 Ghz p4 and a 1 Ghz P3 on the other side.Seems like CPU problem... What procesors did you use? Nstreme is very CPU sensitive... The more, the better :)I used 2.8.10 43 Mbit and 2.8.24 without nstreme 43 mbit with nstreme 23 MbitJohan, I've had similar problems as you've had. Tested at 2M and throughput was around 45-50mbps. Similar type of setup with 2 Intel-based servers just doing a b/w test with the newest betas....