Hi ,
this started when i install 3.20 regular routing package, then i try routing-test , v3.20 and then 3.22
routing table was large so i divide into ospf areas , area 1,2,3 and backbone
routing table in every area was smaller , but when i install routing 3.20, later routing-test all routes are same on every router in every ospf area.
i say again , i know its test package but cant belive that its made retrogradation.
Re: v3.22 OSPF issue
Hi,
I think these are not too much information. Post your configuration and maybe somebody can help you.
I don't use regular routing package with ospf. There was trouble with it on bigger network. And I think the MT only works on the routing-test package.
I have 239 route in the ospf table now. I had much more but use area ranges to lower the numbers of it. I have only some trouble with the ospf where I use older version (3.9). I'll upgrade these routers because the 3.20 is much more stable. I use 3.22 only for 2 days so I don't have too much information about it.
I think these are not too much information. Post your configuration and maybe somebody can help you.
I don't use regular routing package with ospf. There was trouble with it on bigger network. And I think the MT only works on the routing-test package.
I have 239 route in the ospf table now. I had much more but use area ranges to lower the numbers of it. I have only some trouble with the ospf where I use older version (3.9). I'll upgrade these routers because the 3.20 is much more stable. I use 3.22 only for 2 days so I don't have too much information about it.
Re: v3.22 OSPF issue
Hi,
I have exacly same problem. Was you able to find solution for it?
thx
I have exacly same problem. Was you able to find solution for it?
thx
Re: v3.22 OSPF issue
If area type is default, all routes will be visible in every area.
You can set another area type, or use area ranges, or even routing filters if you don't want specific routes to be imported into backbone area.
You can set another area type, or use area ranges, or even routing filters if you don't want specific routes to be imported into backbone area.
Re: v3.22 OSPF issue
No, problem is that I have totally 3 areas.
1st 0.0.0.0 as backbone
2nd 1.1.1.1 type stub
3nd 2.2.2.2 type stub
problem is that routes from area 1.1.1.1 are also distributed to area 2.2.2.2
any idea what problem could be here?
Also is there any way to group simillar adress spaces on one router to one?
as example I have on one router networks 192.168.0.0/26 192.168.0.64/26 192.168.0.128/26 192.168.0.192/26 and one link to ospf network.
There would be ideal for OSPF just to group these network's to one /24 subnet instead of 4difrerent routes.
thank you for help
1st 0.0.0.0 as backbone
2nd 1.1.1.1 type stub
3nd 2.2.2.2 type stub
problem is that routes from area 1.1.1.1 are also distributed to area 2.2.2.2
any idea what problem could be here?
Also is there any way to group simillar adress spaces on one router to one?
as example I have on one router networks 192.168.0.0/26 192.168.0.64/26 192.168.0.128/26 192.168.0.192/26 and one link to ospf network.
There would be ideal for OSPF just to group these network's to one /24 subnet instead of 4difrerent routes.
thank you for help
Re: v3.22 OSPF issue
Need more information,
post your configuration and post output of "/routing ospf lsa print" from the router where you shouldn't see all the routes.
post your configuration and post output of "/routing ospf lsa print" from the router where you shouldn't see all the routes.
Re: v3.22 OSPF issue
Here you go.
It seems I'm unable to upload txt or any other format type to this forum
so my config is here http://jirka.ehm.cz/temp/config.txt
Thank you for any help.
It seems I'm unable to upload txt or any other format type to this forum
so my config is here http://jirka.ehm.cz/temp/config.txt
Thank you for any help.
Code: Select all
/routing ospf lsa print
AREA TYPE ID ORIGINATOR SEQUENCE-NU...
prilepy router 172.25.4.2 172.25.4.2 0x800000C5
prilepy router 172.26.0.10 172.26.0.10 0x800000BE
prilepy summary-n... 0.0.0.0 172.26.0.10 0x800000BD
prilepy summary-n... 172.16.0.0 172.26.0.10 0x800000BD
prilepy summary-n... 172.16.0.4 172.26.0.10 0x800000B3
prilepy summary-n... 172.16.0.8 172.26.0.10 0x800000B3
prilepy summary-n... 172.16.1.0 172.26.0.10 0x800000B3
prilepy summary-n... 172.16.1.64 172.26.0.10 0x800000B3
prilepy summary-n... 172.16.10.0 172.26.0.10 0x80000051
prilepy summary-n... 172.16.10.64 172.26.0.10 0x80000051
prilepy summary-n... 172.16.50.0 172.26.0.10 0x800000BD
prilepy summary-n... 172.16.51.64 172.26.0.10 0x8000001B
prilepy summary-n... 172.16.51.128 172.26.0.10 0x80000076
prilepy summary-n... 172.16.55.0 172.26.0.10 0x8000001B
prilepy summary-n... 172.16.56.0 172.26.0.10 0x80000075
prilepy summary-n... 172.16.57.64 172.26.0.10 0x80000048
prilepy summary-n... 172.16.57.128 172.26.0.10 0x80000048
prilepy summary-n... 172.16.58.0 172.26.0.10 0x8000001B
prilepy summary-n... 172.16.254.0 172.26.0.10 0x80000051
prilepy summary-n... 172.26.0.0 172.26.0.10 0x800000BD
prilepy summary-n... 172.26.246.0 172.26.0.10 0x800000B7
Re: v3.22 OSPF issue
I have modified the permissions of the forum, so now you can also upload TXT and RSC files. Please try it.
You do not have the required permissions to view the files attached to this post.
Re: v3.22 OSPF issue
Everything is correct. You have set inject-summary-lsa=yes in area configuration.
It means that all summary routes will be imported. Also you can see that in lsa output.
It means that all summary routes will be imported. Also you can see that in lsa output.
Re: v3.22 OSPF issue
omg, sorry guys! you are right.
I tested it before with or without this option but I guess that I simply did'nt wait long enough for ospf to reconfigure routes.
Thank you for help!
What about grouping multiple small /26 subnet's to large /24 ?
I tested it before with or without this option but I guess that I simply did'nt wait long enough for ospf to reconfigure routes.
Thank you for help!
What about grouping multiple small /26 subnet's to large /24 ?
Re: v3.22 OSPF issue
You can use area ranges to aggregate routes.
http://wiki.mikrotik.com/wiki/OSPF_and_Area_summaries
http://wiki.mikrotik.com/wiki/OSPF_and_Area_summaries
Re: v3.22 OSPF issue
Hi all,
To be able to summaries multiple routes in one and send them to other ospf arena, do I need to add blackhole route first and routing filter or not?
Ex.:
I have 10.0.4.0/24 and 10.0.5.0/24 networks.
To be able to summaries multiple routes in one and send them to other ospf arena, do I need to add blackhole route first and routing filter or not?
Ex.:
Code: Select all
/ ip route
add dst-address=10.0.4.0/23 distance=254 scope=255 target-scope=10 \
type=blackhole comment="" disabled=no
/ routing filter
add chain=ospf-out prefix=10.0.4.0/23 invert-match=no action=accept comment="" \
disabled=no
add chain=ospf-out invert-match=no action=discard comment="" disabled=no