MikroTik

N2v got nice now, those pics are default config 34 dbi ubnt dish (60km) and 30dbi dish (14km) first DBII F52N, second Ubnt SR71-15, little noise on the first but that card dont care about noise, ping is a little hight due nv2 (2-4 ms ) on both links Nv1 are 1ms both 150-160 mbps

pretty good results indeed,

where do you get v5.9 From, did MT support mailed it to you ?

Yes, you can ask for beta 5.9 the y mail you the full software

Very nice results, especially the 60km link. Can you run a speedtest with tcp traffic and a duplex test?
Also, do you have the power turned down on the SR71-15?

How much bandwidth was between the (same) two links with the version 5.8?
What are (technically) the improvements in version 5.9?

160mbps max and a little high latency (4~10 ms), the real improve its the noise, before a lost 3db of rx and tx on each side, and on rain drops a lot more, now its raining and just dropped a little, tcp test its very limited by cpu 64 mbps, from pc to pc 96mbps on tpc, limited by the lan 100mbps, sorry for my english

160mbps max and a little high latency (4~10 ms),

hello. did you mean NV2 in max speed the latency only at ~ 10ms maximum?

No, was a joke max latency its almost 100 ms but almost full link usage for test, normal use 100mbps max i dont get 20 ms

No, was a joke max latency its almost 100 ms but almost full link usage for test, normal use 100mbps max i dont get 20 ms

nice share. thanks.

wow really nice!!! I start to move my 64kmP2P`s to this 5.9.

best regards!!!

Well ...

Finally some promissing results for a 900MHz XR9 cards, 5MHz BW, both NLOS links.

Untill V 5.7 one of them have the calculated distance wanderin between 5 ... 15Km back and forth. The 5MHz 802.11G calculated distance is 9/10Km ... (the real distance is 2.4Km).

Now ... 5.9 at one RB433 CPE, 5.8 at the RB433 AP and ... 5.8 at the other CPE (WRAP => X86!!!!) ... and it's working ...

In a couple of hours I'll upgrade the AP and later the X86 ...

I'm a bit afraid abt X86 ... because I downloaded the pre-release npk just changing letters at the link for the file routeros- mipsbe-5.9.npk (became routeros-x86-5.9.npk) :-/

Links are up for 45min now. Used to be ... 20 or 30 seconds than starts to disconnect/reconnect.

Regards;

Wow, really impressive. Can you tell me the full hardware you used for the 60km link?(antennas, cards, routerboard).

isnt supposed to NV2 is not yet ready for X86?

isnt supposed to NV2 is not yet ready for X86?

Yes

Atreides: Ubiquiti Rocket Dish 34 Dbi, DBii Network R52N and RB411AH (Ubitik it came with the case for mounting on the dish directly and the router with the card from Baltic Network)

Yes, you can ask for beta 5.9 the y mail you the full software

i write but i don't get any response. Any link is available to get beta?

PS. forgive me for my poor english.

GREAT post, Thanks
Could you post allso a screenshot from the Wireless and Advanced tabs of the WLAN interface.
Thank you fo rthe post

Hello,

Can you share all the settings? Like HT, HT MCS,

Thanks

try also ping. When I changed 802.11a to nv2, latency got worse from 2ms without nv2 to 7,5ms with nv2(when there is no traffic).
Bandwitch test: tcp: 18mbit, udb: 39mbit. Ping max. 20ms.Why is so big difference between tcp and udp using nv2?

here is ping:
http://i42.tinypic.com/14x0655.png

Hi
For SR71-15 are you using default power profile?

Is that performance reached using bridge? Or vpls?

Atreides: Ubiquiti Rocket Dish 34 Dbi, DBii Network R52N and RB411AH (Ubitik it came with the case for mounting on the dish directly and the router with the card from Baltic Network)

Nice to see more people using Mikrotik in the country!!

Saludos,

J