Page 1 of 1
Changelog RouterOS 6.7
Posted: Sun Nov 10, 2013 12:45 am
by Stillhard
Changelogs for upcoming RouterOS 6.7
- What's new in 6.7rc1 (2013-Nov-08 15:54):
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
Re: Changelog RouterOS 6.7
Posted: Tue Nov 12, 2013 6:04 pm
by honzam
What's new in 6.7rc1 (2013-Nov-15 10:45):
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
Re: Changelog RouterOS 6.7
Posted: Sat Nov 16, 2013 6:23 am
by Stillhard
- What's new in 6.7rc1 (2013-Nov-15 15:23):
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
Re: Changelog RouterOS 6.7
Posted: Wed Nov 20, 2013 10:49 am
by kometchtech
6.7rc1 version up in November 19? It seems to use, but do you know What changes?
Best regards
Re: Changelog RouterOS 6.7
Posted: Thu Nov 21, 2013 11:26 pm
by armandfumal
What's new in 6.7rc1 (2013-Nov-20 14:13):
*) dhcpv4 server - added REMOTE_ID option variable for relayed packets;
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels when policy uses protocol filter;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
Re: Changelog RouterOS 6.7
Posted: Fri Nov 22, 2013 10:50 am
by kometchtech
Thanks!
Re: Changelog RouterOS 6.7
Posted: Fri Nov 22, 2013 6:07 pm
by TonyJr
What's new in 6.7rc2 (2013-Nov-22 15:45):
*) leds - inverted modem signal trigger, now it will trigger when the signal level rises above the treshold;
*) ipsec - added sha256 and sha512 support;
*) ipsec - proposal defaults changed to aes-128 and sha1 for both phase1 and phase2;
*) certificate - support ip, dns and email subject alternative names;
*) dhcpv4 server - added REMOTE_ID option variable for relayed packets;
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels when policy uses protocol filter;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
Re: Changelog RouterOS 6.7
Posted: Sat Nov 23, 2013 5:19 pm
by D1M0N
Where can I download 6.7rc2 ???
Re: Changelog RouterOS 6.7
Posted: Mon Nov 25, 2013 3:11 pm
by kometchtech
What's new in 6.7 (2013-Nov-25 10:22):
*) leds - inverted modem signal trigger, now it will trigger when the signal level rises above the treshold;
*) ipsec - added sha256 and sha512 support;
*) ipsec - proposal defaults changed to aes-128 and sha1 for both phase1 and phase2;
*) certificate - support ip, dns and email subject alternative names;
*) dhcpv4 server - added REMOTE_ID option variable for relayed packets;
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels when policy uses protocol filter;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
Re: Changelog RouterOS 6.7
Posted: Tue Nov 26, 2013 10:10 am
by maxiscool
Hi,
Do we know when 6.7 will be release?
Thanks.
Re: Changelog RouterOS 6.7
Posted: Tue Nov 26, 2013 10:28 am
by janisk
there is no release date set.
also 6.7rc2 has some special ppp patches, look more here regarding 6.7rc2
http://forum.mikrotik.com/viewtopic.php?f=2&t=79166&
Re: Changelog RouterOS 6.7
Posted: Tue Nov 26, 2013 4:03 pm
by honzam
What's new in 6.7 (2013-Nov-26 09:57):
*) poe - new poe controller firmware for RB750UP and OmniTIK UPA;
what changes?
Re: Changelog RouterOS 6.7
Posted: Tue Nov 26, 2013 4:35 pm
by janisk
it should be more precise and report proper values as there where issues observed that sometimes unrealistic reading was displayed.
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 4:59 am
by willy
Sorry for a possible many asked question, but generally available anywhere the development releases of routeros? My devices affected in a bug in 6.6 (vlan on bridge), and i will be try, but also useful for "advanced" users used with caution. If not accessible generally, please give me download link for 6.7rc1. Thanks.
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 9:23 am
by honzam
write to support for acceess to prerelease page
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 2:19 pm
by dadaniel
it should be more precise and report proper values as there where issues observed that sometimes unrealistic reading was displayed.
could you please comment on the following questions:
which max. initial PoE current is possible with the current hardware/firmware?
which protection is built in and is it reversible/replaceable?
thank you very much!
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 2:56 pm
by janisk
as far as it should concern end-users - it is as before. Also, fw upgrade procedure is simplified.
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 6:28 pm
by Malosa
There is a bug with PPPoE client in RouterOS 6:
http://forum.mikrotik.com/viewtopic.php?f=2&t=78875
Basically the <<AC-Name=''>> folder in the request must be sent even if it's empty, like other routers do, but Mikrotik doesn't.
It's very important because some modems cannot be used. And it's an extremely easy bug to correct.
Thank you.
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 7:21 pm
by skot
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
Glad to get these features. They show up in CLI but not winbox/webfig.
Re: Changelog RouterOS 6.7
Posted: Wed Nov 27, 2013 11:09 pm
by armandfumal
What's new in 6.7 (2013-Nov-26 09:57):
*) poe - new poe controller firmware for RB750UP and OmniTIK UPA;
*) ipsec - added aes-ctr encryption mode;
*) leds - inverted modem signal trigger, now it will trigger when the signal level rises above the treshold;
*) ipsec - added sha256 and sha512 support;
*) ipsec - proposal defaults changed to aes-128 and sha1 for both phase1 and phase2;
*) certificate - support ip, dns and email subject alternative names;
*) dhcpv4 server - added REMOTE_ID option variable for relayed packets;
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels when policy uses protocol filter;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
*) fixed l2mtu changing on CCRs - could cause port flapping;
*) disabling/enabling ethernet ports did not work properly on CCRs - could cause port flapping;
Re: Changelog RouterOS 6.7
Posted: Thu Nov 28, 2013 2:53 pm
by honzam
What's new in 6.7 (2013-Nov-28 12:53):
*) support Android usb tethering interface;
*) ipsec - added aes-gcm icv16 encryption mode;
*) wireless - improve rate selection for nstreme protocol
*) poe - new poe controller firmware for RB750UP and OmniTIK UPA;
*) ipsec - added aes-ctr encryption mode;
*) leds - inverted modem signal trigger, now it will trigger when the signal level rises above the treshold;
*) ipsec - added sha256 and sha512 support;
*) ipsec - proposal defaults changed to aes-128 and sha1 for both phase1 and phase2;
*) certificate - support ip, dns and email subject alternative names;
*) dhcpv4 server - added REMOTE_ID option variable for relayed packets;
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels when policy uses protocol filter;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
*) fixed l2mtu changing on CCRs - could cause port flapping;
*) disabling/enabling ethernet ports did not work properly on CCRs - could cause port flapping;
*) fixed port flapping on CCR - could happen when having other than only-hardware-queue interface queue.
Note that having other interface queue than only-hardware-queue dramatically reduces performace, so should be avoided if possible;
Re: Changelog RouterOS 6.7
Posted: Thu Nov 28, 2013 3:09 pm
by macgaiver
*) fixed port flapping on CCR - could happen when having other than only-hardware-queue interface queue.
This is interesting - so basically if you have any queue tree and /interface queue isoverrided by it you can also might be affected by this issue....
Re: Changelog RouterOS 6.7
Posted: Fri Nov 29, 2013 3:33 am
by fernandolcx
*) support Android usb tethering interface;
This is what I'm talkig about!
Re: Changelog RouterOS 6.7
Posted: Fri Nov 29, 2013 4:34 pm
by kometchtech
What's new in 6.7 (2013-Nov-29 13:37):
*) support Android usb tethering interface;
*) ipsec - added aes-gcm icv16 encryption mode;
*) wireless - improve rate selection for nstreme protocol
*) poe - new poe controller firmware for RB750UP and OmniTIK UPA;
*) ipsec - added aes-ctr encryption mode;
*) leds - inverted modem signal trigger, now it will trigger when the signal level rises above the treshold;
*) ipsec - added sha256 and sha512 support;
*) ipsec - proposal defaults changed to aes-128 and sha1 for both phase1 and phase2;
*) certificate - support ip, dns and email subject alternative names;
*) dhcpv4 server - added REMOTE_ID option variable for relayed packets;
*) ipsec - fix policy bypass on IPv6 gre, ipip, eoip tunnels when policy uses protocol filter;
*) userman - fix crash on tilera;
*) fixed hairpin nat on bridge with use-ip-firewall=yes;
*) fixed vlan on bridge after reboot having 00:00:00:00:00:00 mac address;
*) address-list - allow manually adding timeoutable entries;
*) address-list - show dynamic entry timeout;
*) fixed l2mtu changing on CCRs - could cause port flapping;
*) disabling/enabling ethernet ports did not work properly on CCRs - could cause port flapping;
*) fixed port flapping on CCR - could happen when having other than only-hardware-queue interface queue.
Note that having other interface queue than only-hardware-queue dramatically reduces performace, so should be avoided if possible;
Re: Changelog RouterOS 6.7
Posted: Sat Nov 30, 2013 9:58 am
by ckgth
Hello,
we have Update an CCR-1036-12G-4S from 6.5 now to testing 6.7 because of port-flapping with 100MB Ports (this was absolutely not acceptable) and now we have "reboot by watchdog timer". With 6.5 this was not! No supout was generated....
Hey MT! I known, the price for this device in resources this have very,very good, but you *must* make Software, who control it good, basically of the standard network processes. I must have an good routing, but no "support for Android". This you can make later....What is with the slogan "Routing the World"?
You wrote in the change-log:
*) fixed l2mtu changing on CCRs - could cause port flapping;
*) disabling/enabling ethernet ports did not work properly on CCRs - could cause port flapping;
*) fixed port flapping on CCR - could happen when having other than only-hardware-queue interface queue.
I must think about that you now known this issues? Have you not probe this before you share 6.6 ?
sometimes it is better, to check the software and wait with an release and no release it with failures....
best regards
Christian
Re: Changelog RouterOS 6.7
Posted: Mon Dec 02, 2013 9:10 am
by normis
Hello,
we have Update an CCR-1036-12G-4S from 6.5 now to testing 6.7 because of port-flapping with 100MB Ports (this was absolutely not acceptable) and now we have "reboot by watchdog timer". With 6.5 this was not! No supout was generated....
Hey MT! I known, the price for this device in resources this have very,very good, but you *must* make Software, who control it good, basically of the standard network processes. I must have an good routing, but no "support for Android". This you can make later....What is with the slogan "Routing the World"?
You wrote in the change-log:
*) fixed l2mtu changing on CCRs - could cause port flapping;
*) disabling/enabling ethernet ports did not work properly on CCRs - could cause port flapping;
*) fixed port flapping on CCR - could happen when having other than only-hardware-queue interface queue.
I must think about that you now known this issues? Have you not probe this before you share 6.6 ?
sometimes it is better, to check the software and wait with an release and no release it with failures....
best regards
Christian
Please send your supout.rif file to support. Make the file after you have the reboot problem.
Re: Changelog RouterOS 6.7
Posted: Sun Dec 08, 2013 2:27 am
by Hotz1
What's new in 6.7 (2013-Nov-26 09:57):
*) poe - new poe controller firmware for RB750UP and OmniTIK UPA;
what changes?
In my brief experience upgrading my test-bench's UPA from 5.26 to 6.7, now a UPA will power
two RB411s in ports 2 and 3, but as soon as you try to power a third RB411 in either ports 4 or 5, they all start power-cycling. This is a mess! What happened?!!!
Fortunately, after downgrading back to 5.26, upgrading the PoE firmware put back the older version (2.1), and now it powers all four RB411s with no problem again.
Maybe this is "old news"; I waited until 6.5 before upgrading from 5.26, figuring any major bugs would have been addressed by now. On all the other equipment, 6.5 worked fine, but this is the first PoE-out device I have tried it on. Did this problem start with PoE firmware in 6.0, or are there some 6.x releases that still work?
Re: Changelog RouterOS 6.7
Posted: Fri Feb 14, 2014 9:06 pm
by Arpanet
Please notice:
command
for
has changed to