Hey guys,

Since me and some coworkers had very bad experiences with the provider supplied router/modems we've bought 5 mikrotik RB2011UiAS-2Hnd devices.

But we cant get good troughput with wireless networks the speed we are getting fluctuate a LOT i've seen 80Mbps once on www.speedtest.net but must of the time it fluctuates between 5Mbps and 15Mbps

On a wired connected i'm reaching the full 180Mbps download speed. To be honoust we've been trying a lot and we are clueless where we should look and what we are doing wrong. The config of my wireless interfaces is as follows

[admin@MikroTik] /interface wireless> print detail
Flags: X - disabled, R - running
0 R name="wlan1" mtu=1500 mac-address=4C:5E:0C:2C:2F:CF arp=enabled
interface-type=Atheros AR9300 mode=ap-bridge ssid="MikroSaga" frequency=2437
band=2ghz-onlyn channel-width=20/40mhz-eC scan-list=default wireless-protocol=802.11
vlan-mode=no-tag vlan-id=1 wds-mode=disabled wds-default-bridge=none
wds-ignore-ssid=no bridge-mode=enabled default-authentication=yes
default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no
security-profile=Private Network compression=no


[admin@MikroTik] /interface wireless> monitor wlan1
status: running-ap
channel: 2437/20-eC/gn
wireless-protocol: 802.11
noise-floor: -95dBm
overall-tx-ccq: 89%
registered-clients: 1
authenticated-clients: 1
wmm-enabled: yes
current-tx-powers: 1Mbps:27(27/30),2Mbps:27(27/30),5.5Mbps:27(27/30),11Mbps:27(27/30),
6Mbps:27(27/30),9Mbps:27(27/30),12Mbps:27(27/30),18Mbps:27(27/30),
24Mbps:27(27/30),36Mbps:26(26/29),48Mbps:25(25/28),54Mbps:24(24/27),
HT20-0:27(27/30),HT20-1:27(27/30),HT20-2:27(27/30),HT20-3:27(27/30),
HT20-4:27(27/30),HT20-5:27(27/30),HT20-6:25(25/28),HT20-7:22(22/25),
HT40-0:27(27/30),HT40-1:27(27/30),HT40-2:27(27/30),HT40-3:27(27/30),
HT40-4:27(27/30),HT40-5:27(27/30),HT40-6:25(25/28),HT40-7:22(22/25)
notify-external-fdb: no


[admin@MikroTik] /interface wireless> /interface print
Flags: D - dynamic, X - disabled, R - running, S - slave
# NAME TYPE MTU L2MTU MAX-L2MTU MAC-ADDRESS
0 R ether1-gateway ether 1500 1598 4074 4C:5E:0C:2C:2F:C5
1 S ether2 ether 1500 1598 4074 4C:5E:0C:2C:2F:C6
2 S ether3 ether 1500 1598 4074 4C:5E:0C:2C:2F:C7
3 S ether4 ether 1500 1598 4074 4C:5E:0C:2C:2F:C8
4 S ether5 ether 1500 1598 4074 4C:5E:0C:2C:2F:C9
5 S ether6-master-local ether 1500 1598 2028 4C:5E:0C:2C:2F:CA
6 S ether7-slave-local ether 1500 1598 2028 4C:5E:0C:2C:2F:CB
7 S ether8-slave-local ether 1500 1598 2028 4C:5E:0C:2C:2F:CC
8 S ether9-slave-local ether 1500 1598 2028 4C:5E:0C:2C:2F:CD
9 S ether10-slave-local ether 1500 1598 2028 4C:5E:0C:2C:2F:CE
10 sfp1-gateway ether 1500 1598 4074 4C:5E:0C:2C:2F:C4
11 RS wlan1 wlan 1500 1600 4C:5E:0C:2C:2F:CF
12 R bridge-local bridge 1500 1598 4C:5E:0C:2C:2F:C6

How much bandwidth are provided from your ISP?

I'm getting 180/18 wired its no issue reaching the speeds co-worker who also bought the device has the same speeds and has an 120 connection

Its written above, he reaches 180 mbit/s by lan cable

Gesendet von meinem HTC Flyer P510e mit Tapatalk 2

Try differnt firmware like 5.26 or 6.4

Gesendet von meinem HTC Flyer P510e mit Tapatalk 2

Well, this is going worse and worse at this moment i see an "excelent" signal strenght but i cant connect to the wireless 1 floor down i do get connection but a lot of the time i'm just getting connected @ like 5Mbps

[admin@MikroTik] > /interface wireless export compac
# jul/16/2014 18:21:06 by RouterOS 6.13
# software id = SVNH-VAJW
#
/interface wireless set [ find default-name=wlan1 ] antenna-gain=5 band=2ghz-b/g/n \ channel-width=20/40mhz-ht-above country=netherlands disabled=no \ frequency=2427 frequency-mode=superchannel l2mtu=2290 mode=ap-bridge \ ssid=MikroTikSaga wireless-protocol=802.11

/interface wireless security-profiles set [ find default=yes ] authentication-types=wpa-psk,wpa2-psk mode=dynamic-keys \ wpa-pre-shared-key=************ wpa2-pre-shared-key=*******

in the debug log is only :

Time Jul/16/2014 18:42:59
Buffer memory
Topics
wireless
debug
Message wlan1: E8:99:C4:9F:43:E0 attempts to associate

Time Jul/16/2014 18:42:59
Buffer memory
Topics
wireless
debug
Message wlan1: E8:99:C4:9F:43:E0 not in local ACL, by default accept

this is about the mac i'm trying to connect with


i've tried different software packages different frequency-modes different countries i dont know where to look anymore

Link quality depends on both sides. May be that the client's signal level is too close to noise level at ap.

Fine tuning the wireless performance may prove harder than you think, especially indoors.
First of all, I would not recommend to connect to an AP which is in a different floor, because the signal is greatly influenced by the structure of the building itself.
Second, how far are the APs from each other? Are they operating on the same frequency?
Third, how far is the client from the AP? IF they are really close, would suggest to go with as higher frequency as possible, like 2462MHz. Also, try to reduce the power output of the wireless of the AP so to keep the connection signal at nearly -60.